Blue Line Innovations PowerCost Monitor Uživatelská příručka stáhnout pdf

Blue Line PowerCost Monitor — 1

Front Back

Top

PowerCost Monitor

User Guide

Install your PowerCost Monitor

™

before reading this Guide

BUTTON FUNCTION

$ Dollars & Cents Mode Displays values in Dollars and Cents and cents

per kilowatt-hour.

KW Kilowatt Mode Displays values in Kilowatts and Kilowatt-hours.

CLEAR Reset totals Press and hold to reset the consumption totals to zero.

12/24 Time Format Press to switch the clock between 12-hour and 24-hour

time display format.

ºC/ºF Temperature Format Press to switch between Celsius and Fahrenheit degrees

temperature display format. NOTE: You see the temperature

at the meter location, where your Sensor Unit is mounted,

and not the ambient temperature of your house (unless

your meter is located inside your house).

MODE Factory Reset Press simultaneously with the SET key to reset the Display

Unit to its factory default values.

LIGHT Backlight Press to illuminate the display backlight for 5 seconds

Current Consumption –Top Row

The top row displays your current energy consumption. If you

press the $ button, you see the value in dollars and cents per hour.

If you press the KW button, you see the value in kilowatts.

The value displayed is directly linked to the rate at which the Disk

Emulator spins: the faster it spins, the greater the rate of energy

consumption and the higher the dollars-per-hour or kilowatts

value you will see on the screen.

In the examples on the right, you are currently using $0.83/hour

(top) and 5.2 kW (bottom) worth of electricity.

IMPORTANT: If your Display Unit shows unusually low

consumption (0.4 KW or less) for an extended period of time

when you are performing normal household tasks such as

cooking or laundry, your Sensor Unit may be misaligned.

See the Troubleshooting section on the reverse side.

Dollars & Cents Mode

($ Button)

Kilowatt Mode

(KW Button)

Consumption Totals – Third Row

The value in the third row shows the cumulative total of

electricity consumed since you last reset the totals. Pressing

the $ and KW buttons toggles the display from dollars and cents

to kilowatt/hours respectively. In the examples on the right, you

have used $27.09 (top) and 36.9 kWh (bottom) worth of electricity

since you last reset the totals.

When the Display Unit is in Dollars and cents mode (

$ key), the

displayed total is replaced, every 10 seconds for 2 seconds, by the

electricity rate you are currently paying according to the values you

entered when setting up your billing rate structure.

Dollars & Cents Mode

($ Button)

Kilowatt Mode

(KW Button)

1 2 3 4

Shrnutí obsahu

Strany 1 - PowerCost Monitor

Blue Line PowerCost Monitor — 1Front BackTopPowerCost MonitorUser GuideInstall your PowerCost Monitor™before reading this GuideBUTTON FUNCTION$ Dollar

Strany 2 - Loss of Signal Display

Blue Line PowerCost Monitor — 2Status – Second RowThe Disk Emulator spins counter-clockwise at a speed proportionalto the rate at which you consume el

Strany 3

Blue Line PowerCost Monitor — 3Troubleshooting - Page 1QAQAQAQAPowerCost MonitorQAQAQAIf you do not see your problem listed here, or you are still una

Strany 4

Blue Line PowerCost Monitor — 4Troubleshooting - Page 2QAPowerCost MonitorQAQAQAQAThe power usage shown on my Display Unit is not updating or isunusua

Další dokumenty pro Meteorologické stanice Blue Line Innovations PowerCost Monitor

Zobrazit dokument Blue Line Innovations PowerCost Monitor Uživatelská příručka

Blue Line Innovations PowerCost Monitor Uživatelská příručka (12 stránky)

Komentáře k této Příručce

Žádné komentáře

Blue Line Innovations PowerCost Monitor Uživatelská příručka

Procházejte online nebo si stáhněte Uživatelská příručka pro Meteorologické stanice Blue Line Innovations PowerCost Monitor. Blue Line Innovations PowerCost Monitor User guide Uživatelská příručka

Shrnutí obsahu

Další dokumenty pro Meteorologické stanice Blue Line Innovations PowerCost Monitor

Komentáře k této Příručce